It’s important when first receiving your new camera to go through the following setup procedures. This not only helps you learn how to navigate the different camera modes but also ensures you know the function of each button. This lesson will guide you through the basic setup procedure.

Charge the CameraInsert the Memory CardLearn the ButtonsPhoto/Video ModesSetup the Date/TimeDisable Loop Recording

Before you rush out and start shooting video there are a few simple steps your should take to ensure your getting the most out of your new action camera. Follow along and we’ll show you the action camera quick start guide to using your new SJCAM SJ4000 Series Action Camera.

Charging the SJ4000

Prior to setup, we recommend you fully charge the camera by using the included USB cable. By either plugging the camera into an available USB port on your computer or by using a compatible 5 volt 1 amp USB power adapter (wall charger). The first initial charge will take approximately 3 hours to complete. The charging status is indicated by the LED status light shown below.

Once fully charged the Red LED will turn off. Your camera is now ready to use.

SJCAM SJ4000 Series Basic WIFI Button Diagram


Insert the Memory Card

We recommend using a Class 10 32GB (or less) microSDHC memory card with the SJ4000 Series Action Cameras. Xtreme Sport DV offers the Sandisk Ultra 32GB Memory Cards for a great price, so if you haven’t already purchased one with your camera head on over to pick one up! If your experiencing intermittent camera freeze-ups or glitchy video recordings, the memory card your using is to slow. Either replace the card with a faster speed or lower the cameras recording resolution.

When inserting the memory card, do not force or jam the card in. When installed correctly it’ll slide down into the spring-loaded slot with little effort. If the card is going in crooked or with friction then try inserting the other way around.


SJ4000 Buttons

  • OK Button
    • Used to take a picture in photo mode or start/stop video recording in video mode.
    • Used to confirm selections while in the preview mode and camera settings menu.
  • Power / Mode Button
    • Press and hold for 3 seconds to power on/off the camera.
    • With the camera is powered on a single press to toggle between video mode, photo mode, preview mode and the camera settings menu.
  • Up / WIFI Button
    • While in video and photo modes, pressing the up arrow will enable wifi (if equipped). Enabling WIFI will drastically decrease the battery run-time and we only recommend using it while the camera is plugged in or constantly powered using a USB battery bank.
    • While in video and photo modes holding the up button will zoom in.
    • While in preview mode and the settings menu the up button will navigate selections “UP”.
  • Down Button
    • While in video and photo modes holding the down button will zoom out.
    • While in preview mode and the settings menu the down button will navigate selections “DOWN”.

SJCAM SJ4000 Series Photo & Video Modes

The SJCAM SJ4000 features several camera modes. To cycle through these modes, press the Power/Mode button on the front of the camera until the desired camera mode is located.

The SJ4000 defaults to full HD 1080p video at 30fps. Once the camera is powered on, you’re ready to shoot video. To start/stop recording, press the OK button.

Photo mode is accessed by pressing the Power/Mode button one time from the video mode default setting.


To preview video and photos stored on the memory card, press the Power/Mode button to toggle to the playback screen.


Setting the Date/Time on the SJ4000

  • To change the date and time on the camera first start by powering on the SJ4000 camera and navigating to the settings menu. After power-up this will be 3 presses on the “Power/Mode” button.
  • Find the “Date/Time” setting by repeatedly pressed the up or down arrows. Confirm your highlighted selection by pressing the “OK” button.
  • Using the up/down arrows, set the year. Confirm the selection by pressing the “OK” button. Continue this step to set the month, day and time fields.
  • Once the correct date/time has been entered confirm and save the settings by pressing the “Power/Menu” button. You will be returned to the main settings menu.


The SJCAM SJ4000 in it’s default state will have the timestamp setting enabled. This setting will overlay the current Date/Time we previously setup onto your video and picture files. Depending on your requirements, you may want to disable this setting. You may do so from the settings menu.


SJ4000 Loop Recording

We HIGHLY recommend turning the loop recording setting OFF in almost all situations. Leaving this enabled may result in data loss. One of the only situations this should be enabled is for dash camera usage.

With loop recording enabled the camera will record a bunch of video files based on the interval selected in the settings. Once the memory card becomes full the camera will automatically delete the oldest video file to make room for the new file.

Mounting Examples

Waterproof Case

White Waterproof Camera Action Cam

Top Helmet Mount

Helmet Camera Mounted Action Cam

Side Helmet Mount

Helmet Camera Mounted Action Cam

Bike/Handle Bar Mounting

Mountain Bike Handle Bar Mount